DIGITEN G3/4″ Water Flow Hall Sensor Switch Flow Meter Flowmeter Counter 1-60L/min


DIGITEN - Frequency: F=5. 5 * q l / min, error:2% voltage :3. 5-24vdc, current can not exceed 10ma, 330 pulses/liter, F=onstant * units of flow L / min * time seconds. Working voltage range:DC 5-18 V. Cable length:15cm. Flow range:1-60l/min maximum current:15 madc 5v working voltage range:dc 5-24 v load capacity:≤10 mADC 5V Operating Temp:≤80℃, Operating humidity:35%¡«90%RH Allow compression:Water pressure 1.

75 mpa below insulation resistance:>100m ohm storage temperature:-25℃~+80℃ Storage humidity:25%~95%RH Output Waveform:Square Wave, output pulse singal. Easy to install. Waterproof, Heat resistance, pressure resistance, cold resistance. Packaging include Flowmeter x 1 Flow range:1-60L/min. Rohs compliant.

DIGITEN G3/4" Water Flow Hall Sensor Switch Flow Meter Flowmeter Counter 1-60L/min - Allow compression:Water pressure 1. 75 mpa below. Output waveform:Square Wave, output pulse signal. Sensor:Hall effect.

More information about DIGITEN

DIGITEN G1" Water Flow Hall Effect Sensor Switch Flow Meter Flowmeter Counter 1-60L/min


DIGITEN - Flow range:1-60l/min maximum current:15 madc 5v working voltage range:dc 5-24 v load capacity:¡Ü10 mADC 5V Operating Temp:¡Ü80¡æ, Operating humidity:35%¡«90%RH Allow compression:Water pressure 1. 75 mpa below insulation resistance:>100m ohm storage temperature:-25¡«+80¡æ Storage humidity:25%¡«95%RH Output Waveform:Square Wave, output pulse singal.

Easy to install. Frequency: F=4. 8 * q l / min error:2% voltage :3. 5-24vdc, current can not exceed 10ma, 450 output pulses/liters, F=onstant * units of flow L / min * time seconds. Packaging include Flowmeter x 1 Flow range:1-60L/min. Waterproof, pressure resistance, Heat resistance, cold resistance. Allow compression:Water pressure 1.

DIGITEN G1" Water Flow Hall Effect Sensor Switch Flow Meter Flowmeter Counter 1-60L/min - 75 mpa below. Cable length:15cm. Rohs compliant. Working voltage range:DC 5-18 V. Output waveform:Square Wave, output pulse signal. Sensor:Hall effect.

More information about DIGITEN


Similar products



DIGITEN G1/2" Water Flow Hall Sensor Switch Flow Meter Flowmeter Counter 1-30L/min


DIGITEN - Cable length:15cm. Working voltage range:DC 5-18 V. Working voltage range:DC 5-18 V. Easy to install. Allow compression:Water pressure 1. 75 mpa below. Waterproof, Heat resistance, pressure resistance, cold resistance. Rohs compliant. Allow compression:Water pressure 1. 75 mpa below. Flow range:1-30L/min. Packaging include Flowmeter x 1 Flow range:1-60L/min.

Output waveform:Square Wave, output pulse signal. Sensor:Hall effect. Frequency: F=7. 5 * q l / min error: ± 2% voltage :3. 5-24vdc, 450 output pulses/liters, f=onstant * units of flow l / min * time seconds flow range:1-30l/min maximum current:15 madc 5v working voltage range:DC 5-24 V Load capacity:≤10 mADC 5V Operating Temp:≤80℃, current can not exceed 10mA, Operating humidity:35%-90%RH Allow compression:Water pressure 1.

DIGITEN G1/2" Water Flow Hall Sensor Switch Flow Meter Flowmeter Counter 1-30L/min - 75 mpa below insulation resistance:>100m ohm storage temperature:-25-80℃ Storage humidity:25%-95%RH Output Waveform:Square Wave, output pulse singal. Output waveform:Square Wave, output pulse signal. Sensor:Hall effect.

More information about DIGITEN


Similar products



DIGITEN Water Liquid Flow Rate Volume Digital Display Flowmeter Quantitative Controller Counter Liter Gallon


DIGITEN - Features quantitative control controller will turn off the solenoid value automatically when flow reach to the setting value you desire monitor flow rate display the real-time volume of liquid which passes per minute work with all hall effect flow sensor it can work various different flow sensor through adjust the k value volume unit display liter or gallon water meter dfc15 can be used to measure the volume of water Adjustable accuracy Calibrate the accuracy through adjust the K parameter Temperature monitor Come with temperature sensor, max 2A Adapter lead length: 1m Measuring Accuracy: ±1% Output for Solenoid valve: 12VDC, flow rated and sensed temperature clearly; custom icons on the display indicate the controller working status at a glance TECHNICAL SPECIFICATIONS Controller Power Requirement: 12VDC Power Adapter: Input: 100-240VAC, it can measure liquid temperature Easy-to-Read Front-Panel Liquid Crystal Display Displays the flow total volume, NTC3950, max 5A Temperature Sensor: 0-100℃/32-212℉, Output: 12VDC, Accuracy: ±1℃/±1℉ thread: M8 Max Total Volume : 999999 G/L Quantitative Range: 0-9999 G/L Flow Rate Range: 0-9999.

99/lpmgpm cable length : 1m dimensions: 88mmx126mmx30mm weight: 200g Operation Environment: Temperature: 0-50℃/32-122℉ Relative Humidity:.

More information about DIGITEN


Similar products



uxcell G3/4" Hall Effect Liquid Water Flow Sensor Switch 3/4 BSP Flowmeter Fluid Meter 2-45L/min SEN-HZ43WB Gold Tone


uxcell US-SA-AJD-122998 - Allow compression:Water pressure 1. 75 mpa below. Output waveform:Square Wave, output pulse signal. Sensor:Hall effect. Monitor flow rate, display the real-tiME volume of liquid which passes per minute. Allow compression:Water pressure 1. 75 mpa below. The water flow sensor is light, nimble outline, small size and easy to install.

Working voltage range:DC 5-18 V. Instantaneous Flow Pulse Characteristic F=8. 1 x qflow-5 +/-10%7. Working voltage range:DC 5-18 V. Quantitative control, controller will turn off the solenoid value automatically when flow reach to the setting value you desire. Work with all hall effect flow sensor, it can work various different flow sensor through adjust the K value.

uxcell G3/4" Hall Effect Liquid Water Flow Sensor Switch 3/4 BSP Flowmeter Fluid Meter 2-45L/min SEN-HZ43WB Gold Tone - The hall effect sensor is sealed from the water pipe and allows the sensor to stay safe and dry. 3. All materials are in line with ROHS testing standards. 3/4 bsp thread, brass material, small size, easy to install. The water flow sensor is applied for water heater, and can be used as flow switch. Maximum water pressure: 1.

More information about uxcell US-SA-AJD-122998


Similar products



DIGITEN 3/4" DC 12V Electric Solenoid Valve Normally Closed N/C Water Inlet Flow Switch


DIGITEN - Allow compression:Water pressure 1. 75 mpa below. Water meter, dfc15 can be used to measure the volume of water. Inlet/outlet ports:3/4" to 3/4", GB screw thread Response Time:ON≤015s, off≤03s rectification: synchronous rectification Pressure:002-08mpa temperature:0-100°c estimated valve life:500, 000 Cycles Filter Screen:Stainless Steel Inlet Filter Flow characteristic:0

02mpa≥3 l/min;01mpa≥12 l/min;08mpa≥35 l/min usage:water and low viscosity fluids. Quantitative control, controller will turn off the solenoid value automatically when flow reach to the setting value you desire. Voltage:dc12v operation mode:N/C, normal close. Large lcd display, displays the flow total volume, flow rate and sense temperature clearly; custom icons on the display indicate the controller working status at a glance.

DIGITEN 3/4" DC 12V Electric Solenoid Valve Normally Closed N/C Water Inlet Flow Switch - Working pressure:002-08mpa. Working voltage:DC12V. Output waveform:Square Wave, output pulse signal.

More information about DIGITEN


Similar products



DIGITEN G1-1/2" 1.5" Water Flow Hall Sensor Switch Meter Flowmeter Control 10-150L/min


DIGITEN . - Output waveform:Square Wave, output pulse signal. Sensor:Hall effect. Flow range:1-30L/min. Work with all hall effect flow sensor, it can work various different flow sensor through adjust the K value. Flow range:10-150L/min. Allow compression:Water pressure 1. 75 mpa below. Output waveform:Square Wave, output pulse signal.

Sensor:Hall effect. Working voltage range:DC 5-18 V. Easy to install. Working pressure:002-08mpa. Water meter, dfc15 can be used to measure the volume of water. Working voltage range:DC 5-18 V. Allow compression:Water pressure 1. 75 mpa below. Monitor flow rate, display the real-tiME volume of liquid which passes per minute.

DIGITEN G1-1/2" 1.5" Water Flow Hall Sensor Switch Meter Flowmeter Control 10-150L/min - Flow range:10-150l/min sensor:hall effect maximum current:15 madc 5v working voltage range:dc 5¡«18 v load capacity:¡Ü10 mADC 5V Operating Temp:¡Ü80¡æ, Operating humidity:35%¡«90%RH Allow compression:Water pressure 1. 75 mpa below insulation resistance:>100m ohm storage temperature:-25¡«+80¡æ Storage humidity:25%¡«95%RH Output Waveform:Square Wave, output pulse signal.

Working voltage:DC12V.

More information about DIGITEN .


Similar products



uxcell G3/4" Waterproof Hall Effect Water Flow Sensor 3/4 BSP Flowmeter Fluid Meter 2-60L/min


uxcell US-SA-AJD-189511 - Temperature:0-100C. Instantaneous Flow Pulse Characteristic F=4. 0x qflow +/-10%6. The bearings used in the rotating part. All materials are in line with ROHS testing standards. 3/4 bsp thread, brass material, small size, easy to install. The water flow sensor is applied for water heater, and can be used as flow switch.

Maximum water pressure: 1. 75mpa, flow range: 2-45L/min. Stable, low water pressure start, high temperature, safe. Operation mode:N/C, normally closed. G3/4", thread male outer diameter: 25. 4mm. Allow compression:Water pressure 1. 75 mpa below. Three wire connection: Red for positive, black for negative, yellow for pulse signal.

uxcell G3/4" Waterproof Hall Effect Water Flow Sensor 3/4 BSP Flowmeter Fluid Meter 2-60L/min - 5. The water flow sensor is light, nimble outline, small size and easy to install. Flow range:1-30L/min. Output waveform:Square Wave, output pulse signal. Sensor:Hall effect. Working pressure:0

More information about uxcell US-SA-AJD-189511


Similar products



DIGITEN Water Flow Control Meter LCD Display Controller+G1/2" Water Hall Sensor Flow Meter Flowmeter Counter 1-30L/min+G1/2" Solenoid Valve Normally Closed N/C+DC 12V Power Adapter


DIGITEN - Technical specificationsfor dfc15 controller:controller power requirement: 12vdcpower adapter: input: 100-240vac; output: 12vdc, max 2a adapter lead length: 1m measuring accuracy: ±1% output for solenoid valve: 12VDC, max 5A Temperature Sensor: 0-125℃/32-257℉, NTC3950, Accuracy: ±1℃/±1℉ thread: M8Max Total Volume : 999999 G/L Quantitative Range: 0-9999.

99 g/l flow rate range: 0-9999. 99/lpmgpm cable length : 1m dimensions: 88mmx126mmx30mm weight: 200g Operation Environment: Temperature: 0-50℃/32-122℉; Relative Humidity:.

More information about DIGITEN


Similar products



12V Plastic Water Solenoid Valve


Adafruit Industries 997 - Also, liquid can only flow one direction. Working voltage range:DC 5-18 V. Here is the current draw table for various voltages. Allow compression:Water pressure 1. 75 mpa below. Nylon and glass fiber made, waterproof and explosion-proof, heat and cold resistant. 3/4 bsp thread, small size, lght weight, easy to install.

Three wire connection: Red for positive, black for negative, yellow for pulse signal. The water flow sensor is applied for water heater, and can be used as flow switch. Maximum water pressure: 1. 75mpa, flow range: 2-60L/min. Large lcd screen】: support reading with liter or gallon unit, lpm/gpM switchable. Temperature:0-100C.

12V Plastic Water Solenoid Valve - Monitor flow rate, display the real-tiME volume of liquid which passes per minute. There are two 1/2\" Nominal NPS outlets. These solenoids are not rated for food safety or use with anything but water. Voltage current6v 160 ma7v 190 ma8v 220 ma9v 240 ma10v 270 ma11v 300 ma12V 320 mA Flow range:1-60L/min. Output waveform:Square Wave, output pulse signal.

Sensor:Hall effect.

More information about Adafruit Industries 997


Similar products



DIGITEN G1/2" Flow Water Sensor Meter+Digital LCD Display Quantitative Control 1-30L/min


DIGITEN - Easy to install, size is small. Output waveform:Square Wave, output pulse signal. Sensor:Hall effect. Specification: working volt: dc24v±8/1a Flow range:1-30L/min LCD size::3inch, built-in backlight. Allow compression:Water pressure 1. 75 mpa below. Flow range:10-150L/min. Password can protect setting value. Monitor real-time flow rate.

Control quantitative flow. When flow reach to the presetting flow, system will output signal for solenoid valveON/OFF. Monitor total flow number. Perfect for your Arduino powered gardening project. Allow compression:Water pressure 1. 75 mpa below. Can connect to flow sensor, temperature sensor, solenoid valve. Monitor gases, liquid flow.

DIGITEN G1/2" Flow Water Sensor Meter+Digital LCD Display Quantitative Control 1-30L/min - Quantitative flow control, total flow alarm. Nylon and glass fiber made, waterproof and explosion-proof, heat and cold resistant. 3/4 bsp thread, small size, lght weight, easy to install. Three wire connection: Red for positive, black for negative, yellow for pulse signal. The water flow sensor is applied for water heater, and can be used as flow switch.

More information about DIGITEN


Similar products